SCHNEIDER
Altivar 71 - variateur de vitesse - 5,5kW 7,5HP - 240V - filtre CEM - terminal - ATV71HU55M3
ATV71HU55M3
Obsolete product, here is the list of products that can replace the reference ATV71HU55M3 :ATV930U55M3 ATV930U75M3
Technical informations
Range of product: | Altivar 71 |
---|---|
Product or component type: | Variable speed drive |
Product specific application: | Complex, high-power machines |
Component name: | ATV71 |
Motor power kW: | 4 kW at 200...240 V single phase5.5 kW at 200...240 V 3 phases |
Motor power hp: | 5 hp at 200...240 V single phase7.5 hp at 200...240 V 3 phases |
Motor cable length: | |
[Us] rated supply voltage: | 200...240 V (- 15...10 %) |
Network number of phases: | Single phase3 phases |
Line current: | 29.9 A for 240 V single phase 4 kW / 5 hp30.8 A for 240 V 3 phases 5.5 kW / 7.5 hp34.9 A for 200 V single phase 4 kW / 5 hp35 A for 200 V 3 phases 5.5 kW / 7.5 hp |
EMC filter: | Integrated |
Assembly style: | With heat sink |
Apparent power: | 7 kVA at 240 V single phase 4 kW / 5 hp12.8 kVA at 240 V 3 phases 5.5 kW / 7.5 hp |
Prospective line Isc: | |
Nominal output current: | 17.5 A at 4 kHz 230 V single phase 4 kW / 5 hp27.5 A at 4 kHz 230 V 3 phases 5.5 kW / 7.5 hp |
Maximum transient current: | 26.3 A for 60 s single phase 4 kW / 5 hp28.8 A for 2 s single phase 4 kW / 5 hp41.3 A for 60 s 3 phases 5.5 kW / 7.5 hp45.3 A for 2 s 3 phases 5.5 kW / 7.5 hp |
Output frequency: | 0.1...599 Hz |
Nominal switching frequency: | 4 kHz |
Switching frequency: | 1...16 kHz adjustable4...16 kHz with derating factor |
Asynchronous motor control profile: | Sensorless flux vector control (SFVC) (voltage or current vector)Flux vector control (FVC) with sensor (current vector)Voltage/frequency ratio (2 or 5 points)ENA (Energy adaptation) system for unbalanced loads |
Type of polarization: | No impedance for Modbus |
Product destination: | Asynchronous motorsSynchronous motors |
---|---|
Supply voltage limits: | 170...264 V |
Supply frequency: | 50...60 Hz (- 5...5 %) |
Network frequency: | 47.5...63 Hz |
Speed range: | 1...100 for asynchronous motor in open-loop mode, without speed feedback1...50 for synchronous motor in open-loop mode, without speed feedback1...1000 for asynchronous motor in closed-loop mode with encoder feedback |
Speed accuracy: | +/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation in closed-loop mode with encoder feedback+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback |
Torque accuracy: | +/- 15 % in open-loop mode, without speed feedback+/- 5 % in closed-loop mode with encoder feedback |
Transient overtorque: | 220 % of nominal motor torque +/- 10 % for 2 s170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes |
Braking torque: | 30 % without braking resistor |
Synchronous motor control profile: | Vector control without speed feedback |
Regulation loop: | Adjustable PI regulator |
Motor slip compensation: | AdjustableNot available in voltage/frequency ratio (2 or 5 points)Automatic whatever the loadSuppressable |
Local signalling: | 1 LED red presence of drive voltage |
Output voltage: | |
Insulation: | Electrical between power and control |
Type of cable: | With a NEMA Type1 kit |
Electrical connection: | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm² / AWG 14L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 6 mm² / AWG 8 |
Tightening torque: | L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 3 N.m / 26.5 lb.inAI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m |
Supply: | Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %, Internal supply, 24 V DC, voltage limits 21...27 V, |
Analogue input number: | 2 |
Analogue input type: | AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + signAI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bitsAI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits |
Sampling duration: | AI1-/Al1+ 2 ms, +/- 0.5 ms for analog input(s)Al2 2 ms, +/- 0.5 ms for analog input(s)LI1...LI5 2 ms, +/- 0.5 ms for discrete input(s)LI6 (if configured as logic input) 2 ms, +/- 0.5 ms for discrete input(s) |
Response time: | AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s) |
Accuracy: | AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °CAI2 +/- 0.6 % for a temperature variation 60 °CAO1 +/- 1 % for a temperature variation 60 °C |
Linearity error: | AI1-/Al1+, AI2 +/- 0.15 % of maximum valueAO1 +/- 0.2 % |
Analogue output number: | 1 |
Analogue output type: | AO1 software-configurable current 0...20 mA, impedance 500 Ohm, resolution 10 bitsAO1 software-configurable logic output 10 V AO1 software-configurable voltage 0...10 V DC, impedance 470 Ohm, resolution 10 bits |
Discrete output number: | 2 |
Discrete output type: | R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cyclesR2A, R2B configurable relay logic NO, electrical durability 100000 cycles |
Minimum switching current: | Configurable relay logic 3 mA at 24 V DC |
Maximum switching current: | R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1,R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1,R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4,R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, |
Discrete input number: | 7 |
Discrete input type: | LI6 |
Discrete input logic: | LI1...LI5 positive logic (source), 11 V (state 0)LI1...LI5 negative logic (sink), > 16 V (state 0), LI6 (if configured as logic input) positive logic (source), 11 V (state 0)LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), |
Acceleration and deceleration ramps: | Automatic adaptation of ramp if braking capacity exceeded, by using resistorS, U or customizedLinear adjustable separately from 0.01 to 9000 s |
Braking to standstill: | By DC injection |
Protection type: | Drive against exceeding limit speedDrive against input phase lossDrive break on the control circuitDrive input phase breaksDrive line supply overvoltageDrive line supply undervoltageDrive overcurrent between output phases and earthDrive overheating protectionDrive overvoltages on the DC busDrive short-circuit between motor phasesDrive thermal protectionMotor motor phase breakMotor power removalMotor thermal protection |
Insulation resistance: | > 1 mOhm at 500 V DC for 1 minute to earth |
Frequency resolution: | Analog input 0.024/50 HzDisplay unit 0.1 Hz |
Communication port protocol: | ModbusCANopen |
Connector type: | 1 RJ45 for Modbus on front face1 RJ45 for Modbus on terminalMale SUB-D 9 on RJ45 for CANopen |
Physical interface: | 2-wire RS 485 for Modbus |
Transmission frame: | RTU for Modbus |
Transmission rate: | 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal9600 bps, 19200 bps for Modbus on front face |
Data format: | 8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal |
Number of addresses: | 1...247 for Modbus1...127 for CANopen |
Method of access: | Slave for CANopen |
Marking: | CE |
Operating position: | Vertical +/- 10 degree |
Height: | 295 mm |
Depth: | 187 mm |
Width: | 175 mm |
Product weight: | 5.5 kg |
Functionality: | Full |
Specific application: | Other applications |
Option card: | CC-Link communication cardController inside programmable cardDeviceNet communication cardEthernet/IP communication cardFipio communication cardI/O extension cardInterbus-S communication cardInterface card for encoderModbus Plus communication cardModbus TCP communication cardModbus/Uni-Telway communication cardOverhead crane cardProfibus DP communication cardProfibus DP V1 communication card |
Noise level: | 55.6 dB conforming to 86/188/EEC |
---|---|
Dielectric strength: | 2830 V DC between earth and power terminals4230 V DC between control and power terminals |
Electromagnetic compatibility: | Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3Voltage dips and interruptions immunity test conforming to IEC 61000-4-111.2/50 µs - 8/20 µs surge immunity test conforming to IEC 61000-4-5 level 3 |
Standards: | EN/IEC 61800-5-1EN/IEC 61800-3EN 61800-3 environments 1 category C3IEC 60721-3-3 class 3C1UL Type 1EN 61800-3 environments 2 category C3EN 55011 class A group 2IEC 60721-3-3 class 3S2 |
Product certifications: | ULCSAC-TickGOSTNOM 117 |
Pollution degree: | 2 conforming to EN/IEC 61800-5-1 |
IP degree of protection: | IP20 |
Vibration resistance: | 1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-61 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6 |
Shock resistance: | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Relative humidity: | 5...95 % without condensation conforming to IEC 60068-2-35...95 % without dripping water conforming to IEC 60068-2-3 |
Ambient air temperature for operation: | -10...50 °C without derating |
Ambient air temperature for storage: | -25...70 °C |
Operating altitude: | 1000...3000 m with current derating 1 % per 100 m |
Warranty period: | 18 months |
Contexte: | 200... 240 V single-phase 200... 240 V / 380... 690 V 3-phase, 50/60 Hz
|
---|---|
Substitution_texte: | Obsolete product, here is the list of products that can replace the reference ATV71HU55M3 : |
Brief
Reference ATV71HU55M3
Product Name Altivar 71 - variateur de vitesse - 5,5kW 7,5HP - 240V - filtre CEM - terminal - ATV71HU55M3
Recently Viewed Products
Related Categories